Z Motorcycle. Service Manual. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, 25, (K) To protect the environment in which we all live, Kawasaki has incorporated crankcase emis-. top > Search for Owner’s Manual (Motorcycle). How to use this service. , , , , , , , , , , , , , . KAWASAKI Z REPAIR MANUAL DOWNLOAD This is the COMPLETE factory service workshop repair manual printed for the KAWASAKI Z
|Published (Last):||26 December 2006|
|PDF File Size:||20.74 Mb|
|ePub File Size:||7.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
Fuel Pressure idling Standard: Place a strip on each journal parallel to the camshaft installed in the correct position. Crankshaft Installation CAUTION If the crankshaft, bearing inserts, or crankcase halves are replaced with new ones, select the bear- ing inserts and check clearance with a plastigage press gauge before assembling engine to be sure the correct bearing mahual are installed.
Owner’s Manuals & Service Manuals | Kawasaki Vehicles
Run the main harness through lower and right side of the thermostat. If the free play is incorrect, adjust the throttle cable see below.
Technical Information — Air Inlet System Then push and turn it further in the same direction and remove the cap. Inlet air temperature sensor trouble Inspect and replace see chapter 3. Take out only the caliper mounting bolts for caliper re- moval.
Joint Connector B Kawasakj. Chain slack – – – Hundreds of pages allow you to print it Main Fuse 30 A It is meant simply as a rough guide to assist the troubleshooting for some of the more common difficulties. Page Also, permanent internal repairs have the advantage of permitting a thorough examination for secondary damage not visible from external inspection of the tire.
Cylinder Head Jacket Joint Connector A 7.
Chain Cover see Final Drive chapter. Make sure the area is well-ventilated and free from any source of flame or sparks; Main Fuse 30 A N. If the axle is damaged or bent, replace it.
Do not use bulb rated for oners wattage then the specified valve. ECU Fuse Installation If a fuse fails during operation, inspect the DFI system to determine the cause, and then replace it with a new fuse of proper amperage.
Be sure to install the oil filler plug [A] after filling the engine oil. Fuel pressure too low or too high Inspect see chapter 3.
Turn the ignition switch OFF. If the fluid level is lower than the lower level line, fill the reservoir to maunal upper level line [C] in the reservoir.
Only appropriate permanent internal repairs are recommended. Check present shim size. We share information about your activities on the site with our partners and Google partners: Torque – Rear Shock Absorber Nuts: Apply molybdenum disulfide grease.
Camshaft Oil Passage 2. Starter Clutch Oil Passage Hole 4. Repair Manual Kawasaki Kle – doc All information contained in this publication is based on the latest product information available at the time of publication.
Service Code 51, 52, 53, 54 Stick Coil 1: Wait until the mufflers cool down. Clutch Lever Free Play Adjustment Mud Guard see Frame chapter. Clutch Lever Free Play Inspection If the connector is clogged with mud or dust, blow it off with compressed air. Download Model Information – Kawasaki Overall width mm Loosen the upper fork clamp bolts [A] and fork top plug [B] before-hand if the fork leg is to be disassembled.
locate a dealer
Never drop the sensor, especially on a hard surface. Torque – Rear Axle Nut: Read the pressure at the average of the maximum and minimum indications. Nanual barrel type Type Bore 38 mm 1. Air cleaner drain hose 4. Got it, continue to print. To Starter Circuit Relay 5. Apply silicone sealant Kawasaki Bond: Oil filler plug 0. Run the hose white through into the throttle cables.