ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
|Published (Last):||5 July 2015|
|PDF File Size:||12.42 Mb|
|ePub File Size:||18.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
A — 10 Standard Speci? Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?
In case of dispute, the offset method of determining yield strength shall be used. These alloys represent an excellent combination of corrosion resistance and fabricability.
HRC typical L Ann 25 min. Only annealed conditions of grades speci? Last previous edition approved in as A — Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonea6666-10or service astm. However, in the case of dispute, tests shall be made by pressure.
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
The noncontrolling factor normally will exceed considerably the speci? Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides. The values obtained in this manner should not, however, be taken as the actual yield strength for 0. In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work.
A666-1 standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh awtm and non-marine applications. Types and L are weldable by most fusion or resistance welding techniques. Permission rights to photocopy the standard may also be secured from the ASTM website www.
One bend test shall be made from one end of each coil.
D PSS means plate, strip, sheet. This revision of Speci? Material Test Report and Certi? Current edition approved Sept. Find out what A666-0 can do for you. Types and L cannot be hardened by thermal treatment. B Type is generally produced with a asm composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Maximum unless otherwise indicated. A number in parentheses indicates the year of last reapproval. The values given in parentheses are for information only. Type L LN Number of Tests 8. C Annealed material that naturally meets mechanical properties may be applied.
If filler metal is required, Type is normally used. The choice of test method for materials in conditions other than annealed shall be at the option of the seller. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Asym, at the address shown below. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.
304 and 304L Stainless Steel
Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: This standard has been approved for use by agencies of zstm Department of Defense.
Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Rockwell B 95 95 Originally q666-10 in Type L should asfm used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool.
and L Stainless Steel – NKS
Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. HardC Elongation in 2 in. Hard Elongation in 2 in.