Instruction Manual, Brother XL Details. Brother Model XL Sewing Machine Instruction Manual, Pages. You May Also Like. Foot Control with Cord. Brother XL manuals and user guides for free. Read online or download in PDF without registration. XL – read user manual online or download in PDF format. Pages in total:

Author: Shakadal Jugore
Country: Bahamas
Language: English (Spanish)
Genre: Software
Published (Last): 14 June 2007
Pages: 162
PDF File Size: 10.97 Mb
ePub File Size: 2.65 Mb
ISBN: 433-3-81759-683-9
Downloads: 36218
Price: Free* [*Free Regsitration Required]
Uploader: Mausida

Are you a Brother Sewing Machine Expert? The thread end should come from the bottom front of the spool. However it downloaded in French. If yes, Make sure your feed dogs are up Do not loosen or tighten the needle clamp screw manal a strong.

Tell us what’s missing. Otherwise, the hook may be damaged.

User’s Guide | Manuals | XL | United States | Brother

If this machine is fitted with a 3 pin non-rewireable BS plug then please read the following. Also See for XL Manual – 42 pages. I know this isn’t what you want to hear but might in the long run be a better solution so that you don’t end up breaking the plastic case.

Brother XL YouTube. Turn the balance wheel toward you until the notch of shuttle aligns with the shelf of manua as shown in the illustration.

Manul the reinforcement fabric under area to be mended. Page of 99 Go.

Brother XL-6562 User Guide

Other needles could break, resulting in damage. By pressing ‘print’ button you will print only current page.


The Elastic Overlock Stitches are useful when sewing stretch materials. If you accidentally step on the foot controller and the machine begins to operate, injury could manaul. Lower the presser foot.

If the wrong presser foot is used, the needle may strike the presser foot and bend or break, and may cause injury. Care should be taken that nothing is placed on the foot controller when the machine is not in use. Stop the machine at the point where you wish to change direction with the needle still in the fabric.

This is a common issue for Brother sewing machines. If the plug fitted is not suitable brtoher the power point in your home manul the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

Always unplug this machine from the electrical outlet immediately after using and before cleaning. It is recommended to practice making a buttonhole on a scrap piece of fabric before attempting it on the actual garment. I doubt that your problem is in the bobbin area. Page 91 Whenever sewing difficulties are encountered, review the section in this instruction manual that details the operation you are performing to make sure you are correctly using the machine.

If no, make sure your bobbin wind spindle is disengaged. Throw away any bent needles. Don’t show me this message again. Lift the presser foot and pull the fabric out gently to the left side.

User’s Guide

Connect the electrical supply plug into a wall outlet. Turn the balance wheel toward you counter-clockwise to raise the needle holder to the highest position.


Change the foot to the Zigzag presser foot. I had to do this on a Viking that I had and ended up having to take it to a dealer to fix because I broher afraid of breaking the plastic clips brotuer the right tools.

Page 36 Reverse sewing is used for back tacking and reinforcing seams. To sew forward, release the Reverse Sewing Lever. Do not lower the Presser Maanual Lever while pushing in the area of the presser foot marked a in fig. Fold over the edges of the two pieces of fabric for the hem and baste the edges to a thin piece of paper leaving a small space between them.

Comments to this Manuals Your Name. If the stitching on the two sides of the buttonhole do not appear uniform, the following adjustments can be made. The machine will then sew forward. Make Model parts diagram. B Quilting design Line 8.

Top 20 Brother XL Mechanical Sewing Questions & Answers – Fixya

Needle holder Needle threader lever Guide Hook holder 5. It’s probably because your upper tension is too loose. Be sure to keep your eye on the needle while sewing. For example, if the distance between the holes is 1.

Check this link, you will probably be able to see how the part is attached.