ISO 14243-1 PDF

Knee wear test ISO /3. Normative References. ISO Implants for surgery – Wear of total knee joint prostheses. Part 1: Loading and displacement. Our equipment allows us to carry out testing with force or displacement controlled kinematics as per ISO (load control) or ISO (displacement. Purchase your copy of BS ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards.

Author: Mooguk Vudojinn
Country: Guadeloupe
Language: English (Spanish)
Genre: Science
Published (Last): 18 August 2015
Pages: 232
PDF File Size: 5.11 Mb
ePub File Size: 10.27 Mb
ISBN: 804-2-66369-152-4
Downloads: 21750
Price: Free* [*Free Regsitration Required]
Uploader: Kazisho

ISO is the governing standard for wear testing of knee prostheses, but there is controversy over the correct direction of anterior-posterior AP displacement and loading and the correct direction of ios rotation TR angles and torque.

This study aimed to analyze 1423-1 altering the direction of AP and TR affected wear on the tibial insert. As such, five loading conditions were applied to FEA models of a knee prosthesis: This study found that changing the input directions for Isl and TR according to ISO —1 and —3 had an influence on the wear rate and wear contours on the tibial insert model.

However, the extent of wear varies depending on the design features of the tibial insert and shape of the input curves.

For displacement control according to ISO —3, changing the direction of AP displacement had a marked influence on the wear rate The clinical relevance of this study is that the results demonstrate that tibial wear is affected by the direction of application of AP and TR. Incorrect application of the loading conditions during the design stage may lead to an ineffective preclinical isk and could subsequently influence implant longevity in clinical use. The success of total knee arthroplasty TKA for returning knee functionality has contributed to its widening application for treating diseases of the knee that ixo failed conservative treatments [ 1 ].

However, even with successive improvements in implant designs and materials, implant failure and patient dissatisfaction still persist [ 2 — 5 ]. Loosening of the implant is the most common reason for requiring a second TKA [ 6 — 8 ], which is reported to be linked to malalignment of the motion axis and the generation of 1243-1 particles which can induce osteolysis around the implant [ 9 — 10 ].

Therefore, in vitro wear testing is an important factor in the development of knee protheses and is a key requirement for regulatory clearance of such devices. ISO is the most commonly used standard for evaluating the wear properties of knee implants [ 11 — 1424-31 ]. There are two control modes for the wear test during 12443-1 gait: The inputs for displacement control are anterior-posterior AP displacement and tibial rotation TR angle, and the inputs for load control are AP load and TR torque.

Io knee simulator used to perform the gait movements requires four inputs; flexion angle, axial load, AP displacement or AP load, TR angle or TR torque. The magnitude and direction of the flexion angle and axial load inputs are same across the ISO range of standards [ 11 — 14 ] Fig 1. According to ISO [ 11 — 142243-1 ], the TR angle is positive when the tibia rotates internally and AP displacement is considered to be positive when the tibia moves anteriorly.

A precise and accurate standard for wear performance is crucial for the development of knee prostheses as it predicts the lifetime of the tibial bearing. ISO —3 is the primary standard for displacement-controlled simulations of wearing of knee prostheses. Compared with the revision of ISO —3, the revision reversed the direction of AP displacement and TR angle but maintained the 142243-1 magnitudes Fig 2.

However, during normal human gait the tibia undergoes positive AP displacement and rotates through a positive TR angle [ 18 — 23 ]. This current study is proposing a modification to ISO —3: ISO —1 is the primary standard for load-controlled simulations of wearing of knee prostheses.

This is due to knee flexion and femoral rollback occurring simultaneously [ 18 — 23 ]. As above, this study is also proposing a modification to ISO —1: A number of studies [ 24 — 29 ] have investigated how varying the parameters outlined in ISO may impact the knee joint; differences in wear between load and displacement control [ 24 — 25 ], the effect of varying the amplitude of inputs for displacement control on wear [ 26 ], the effect of anterior-posterior and internal-external motion constraints on wear [ 27 ], the impact of different activities io the wear performance [ 28 ], comparison between electromechanically- and pneumatically-controlled knee simulators [ 29 ].

  EUROLITE TB-5 PDF

To the best of our knowledge, no previous studies considered the influence of altering the direction of AP and TR on wear rates. A misjudgment or incorrect evaluation in this area may lead to an ineffective preclinical evaluation and subsequently 1424-1 the longevity of the tibial insert in clinical use. A retrieved knee prosthesis PFC, Depuy Isso of the 1423-1 knee was used both to construct the finite element model and for experimental work Fig 4A. An ido of the surfaces of the femoral component and tibia insert found only minor burnishing, abrasion, and scratching, but no obvious cold flow, pitting, embedded metal, delamination or wear through [ 30 ].

The impact of variations in input directions according to ISO on wearing of knee prostheses

In the absence of any marked deformities, the minor surface abrasion was deemed acceptable as it would not have any noticeable influence on knee kinematics. Inconsistencies on the articular surface between the 3D model and the physical PFC implant were controlled to be less than 0. A Retrieved tibial insert from PFC implant; Iao Variations in the articular surface between the 3D model and the retrieved insert were within 0.

The two ios were identical except the load control model had additional nonlinear connector constraints for 114243-1 AP motion and tibial rotation TR according to ISO —1 [ 1214 ]. The tibial insert was modeled as deformable elastic polyethylene Gur with approximately 81, C3D10M elements of size 1 mm for the articular surface and 1.

The femoral component was modeled as a rigid body. A coefficient of friction of 0. The boundary conditions were set according to ISO standards [ 11 — ixo ]. The loading points on the tibia and femur was offset to the medial side by a distance of 0. The mechanical axes described by Grood and Sunday were used [ 32 ]. Input curves were applied to the tibia and only a flexion angle was applied to the femoral side.

For the displacement controlled models Fig 5Athe input curves were AP displacement, tibial rotation TR angle, flexion angle and compression loading. For the load controlled models Fig 5Bthe input curves were AP load, TR torque, flexion angle and compression loading.

Nonlinear constraints in AP and TR 12443-1 were imposed on the load controlled model. Along the AP direction, the constraint stiffness was set oso 9. The tibial insert was free to move in the medial-lateral, anterior-posterior, superior-inferior and valgus-varus directions, as well being free to rotate within the tibial component, but 142431 constrained in flexion.

In contrast, the femoral component was only permitted to move in flexion. The flexion axis was defined as a line connecting the medial and lateral centers of the posterior femoral radius arc. The wear coefficient K was 2.

According to the calculated wear depth, each node on the surface was moved in the direction normal to the articular surface. An adaptive remeshing procedure was employed to simulate the progression of surface wear. It was ido for 5 million cycles according to ISO [ 11 — 14 ]. The volume of wear was calculated by the difference between the initial volume of the tibial insert and its final volume.

Knee wear test ISO

The tibial insert surface was updated everycycles, which has been shown to only have a difference of between 2. The contact pressure was validated using a Tekscan pressure distribution measuring system Tekscan Inc, America S1 File. The following sections detail the validation of the sliding distance and contact areas using wear contours and feedback curves. The calculation process was developed and validated for use in previous studies on TKA in our laboratory [ 34 — 35 ]. As shown in Fig 6Aan electromechanically-controlled knee simulator, Prosim Prosim, Simulation Solutionswas used to perform the gait movements according to the suggested modifications to ISO —3 with a positive AP displacement tibia moves anteriorly and positive TR angle tibia rotates internally.

ABS plastic was used to construct the jigs Fig 6B. 12443-1 the test, the medial and lateral articular surfaces were uniformly coated with small dots using a permanent marker, which was selected as an easy to apply and non-water soluble coating material Fig 6C. A simple template with uniformly spaced holes was used to ensure consistency with positioning of the holes. The loading points on the tibia and femur were offset towards the medial side by a distance of 0.

The flexion axis was the same as the FEA model detailed above. The frequency was set at 1 Hz and the test was performed in the air without a medium.

The wear contours on the tibial insert produced by the Kso model Fig 7A were very similar with the wear patterns produced by the knee simulator Fig 7B.

  JOANNA MONCRIEFF THE MYTH OF THE CHEMICAL CURE PDF

The flexion angle, tibial rotation angle, AP displacement, and axial force were recorded from both the FEA model and experimental setup and then compared with the oso inputs from the modified ISO —3 requirements Fig 8. Fig 8 demonstrates the remarkable similarity between the three sets of data, which confirms the validity of the FEA models introduced in this 12443-1.

For the displacement control models, as shown in Fig 9the graph of AP displacement plotted according to ISO —3: The AP reaction loads are also acting in the opposite direction, but the plot is not symmetrical.

A similar tendency can be seen for tibial rotation whereby the 142443-1 of TR angle plotted according to ISO —3: The corresponding TR torque also isp in the opposite direction, 144243-1 is not symmetrical.

The wear rate, isp wear and maximum wear depth calculated from the FEA models are detailed in Table 2. Fig 10 shows the wear contours for all models. The wear contours from the modified ISO —3 and modified ISO —1 standards are more consistent in comparison to the other models both central and slightly posterior on the tibial insertdemonstrating a more natural knee motion [ 18 — 23 ]. In the displacement control models Fig 10A—10C it can be seen that the wear contours for the modified ISO —3 model are central and slightly posterior on the tibial insert, whereas wearing on the ISO —3: This is due to the reversed input direction for AP displacement.

For load control Fig 10D and 10Ethe wear contours were positioned more anteriorly or posteriorly depending on the direction of the input for AP load. However, the level of wear varies depending on the design features of the tibial insert kso the details of the input curves. Anterior positioning of the knee contact points results in a greater AP load Fig 9 and higher wear rates.

If the insert was not symmetrical, but instead was an anatomical or medial pivot design, reversing the direction of TR angle may have a marked influence on wear. For the load control models, reversing the AP load also isk the wear rate but to a lesser degree than the displacement controlled models. This may be due to the AP load input curves Fig 3 having both positive values and negative ixo. The load control method modified ISO —1 yielded Therefore, for the load control models, the AP load and TR torque inputs resulted in a greater range of AP displacement and TR angles than in the displacement control models Fig 9.

The direction of AP and TR also had a marked influence on the wear contours. In the displacement control models, reversing the direction of AP displacement according to ISO —3 impacted the loading patterns and magnitude, resulting in a marked difference in wear contours.

The impact of variations in input directions according to ISO 14243 on wearing of knee prostheses

The same phenomenon was observed for the load control models ISO —1. Overall, the wear contours from the modified ISO —3 and modified ISO —1 were found to be more consistent than the other models.

This could be explained by most of the AP displacements and TR angles being in a positive direction Fig 9. The FEA model used in this study was fully validated prior to commencing any wear simulations, as highlighted in the following five points.

Previous studies on wearing of knee implants [ 24 — 25 ] failed to consider variations in the direction of AP and TR, which has been shown in this study to be a critical factor in determining knee kinematics and the level of wear on the tibial insert. Similarly, Schwenke T et al. There are a number of limitations to this study that should be noted.

Firstly, the geometrical models and material properties were not sourced directly from the manufacturer, but instead the geometry was based on implant measurements and the material property was defined as UHMWPE Gur This may lead to slight differences against data published by the original manufacturer.

Thirdly, neither the effect of creep nor cross-shear was considered in this study.

Therefore, the current model does provide valuable insight into the influence of AP and TR directions on tibial wear. Isp study also introduces suggested modifications to the ISO standards that that closely resemble in vivo situations.