LENZE 8600 MANUAL PDF

View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. vector. System/Component overview. Lenze. FU vector en 11/ 3. System overview/Selection guide. Communication modules e.g. keypad or. PROFIBUS. Get Lenze IB Manual. Get all Lenze manuals! with optical fibre cable together with the controller series as of E DC controller E 5x. 6x.

Author: Akinojin Gale
Country: Laos
Language: English (Spanish)
Genre: Politics
Published (Last): 11 July 2006
Pages: 126
PDF File Size: 1.79 Mb
ePub File Size: 10.53 Mb
ISBN: 271-2-55129-606-8
Downloads: 63013
Price: Free* [*Free Regsitration Required]
Uploader: Zugul

Strings or data blocks cannot be transmitted. Notes which should be observed to avoid possible damage to or destruction of equipment. The parameter is mapped via the ramp-min function to the Lenze deceleration ramp L-C By increasing the chopper frequency you tan generally reduce the motor noises which are generated by the pulsating output voltage.

Configuration | Lenze EDSU-REG User Manual | Page /

Minimum Field Frequency Fdmin Page 5 Contents Planning 1. Parameter Setting By Two Codes 2.

The slack which occurs between the two conveyor belts is kept constant by the loop control. Page 3 use these Operating lnstructions All digital inputs and Outputs are PLC compatible and are – manula operated with an external voltage supply 24 V – isolated from the rest of the control Stage. Parameters printed in bold show the factory setting.

Lenze | DACPOL SERVICE

Technical Data Of Brake Resistors 6. Because of the generation of leakage currents, the RFI filters must be connected to earth.

  KUMAR MANGALAM BIRLA COMMITTEE REPORT PDF

Wiring Wiring Power connections cabinet All power terminals remain live up to 3 minutes after mains disconnection! Values in the binary format 0,1. Global drive frequency inverters 0. You can activate it by using a switch.

Control word hex Data format: Monitor Outputs The controller has two monitor Outputs terminals 62 and 63to output internal Signals as voltage or current Signals.

DP process data 3. Page 8 9 Dancer-Position control 9.

What’s missing? Tell us about it.

The DP parameter setting channel has the same structure for both directions of transmission. For double word parameters 32 bit3 bytes are not used. Speed quick stop Ahex 4. The controller is inhibited and waits for controller enable. E32 ,5A9A Bit We distinguish between two operating modes: The inforrnation is identical with that under C, with the differente that you tan read the controller value directly thus excluding conversion errors.

Digital frequency output X9 Option The connection of drives via digital frequency allows a simple and or Slave drives. Lenze data types The possible Lenze parameters with their ranges are listed in the corresponding operating instructions. The large setting ranges of the control Parameters also allow the control of an application datum if this depends on the drive Speed.

That means, the drive could accelerate to fmax while adjusting the inputs when the setting controller enable is activated, although only a very small setpoint was Here, the field frequency input via terminal 8 or via the digital frequency input or via code CO46 is used to limit the maximum field frequency. Gain Adjustment – Radius Signal 9.

  APERTURE FILETYPE IMMERSION NUMERICAL OBJECTIVE OIL PDF

Setting Of The Torque Controller Relays with gold-plated contacts have proven for this. These Operating Instructions are valid for the units with the following nameplate data: Settings for the master Most of the controller manufacturers demand a controller description file controller master data file.

With cyclic overload, the ratio between overload to cycle time must not exceed 0.

Basic nanual Operating mode The controllers of the series offer different interfaces. Page 84 – Functions of the freely assignable digit Process data can be divided into process output data PO data and process input data PI dataviewed from the master, that means PO data are input data for the controller.

Commissioning sequence The initial commissioning of the IB bus interface module together with a controller and possibly an automation maual is divided into the following phases: As standard, you can connect a maximum of 32 participants including hosts to the RS bus.

Ensure unimpeded Ventilation of cooling air. EC directives are issued by the European Council and are intended for the determination of common technical requirements harmonization and cet-tification procedures within the European Community.