Lexmark Cn. Network. Service Manual. xxx. Assembly 1: Operator panel assembly, Cdn/Cn/Cdn. 6. 40X 1. 1. Bezel. Lexmark C Pdf User Manuals. View online or download Lexmark C User Manual, Troubleshooting Manual, Quick Reference. View and Download Lexmark C service manual online. Service Manual. C Printer pdf manual download. Also for: Cn, C, C, C, C
|Published (Last):||5 September 2007|
|PDF File Size:||10.9 Mb|
|ePub File Size:||2.35 Mb|
|Price:||Free* [*Free Regsitration Required]|
A page similar to this one prints: Handing The Photoconductor Unit Page xxx Looking down at the keyed end of the restraint Ctwist the end clockwise, slide the restraint upward through the slit Dand slip the end of the restraint through the keyed hole E.
Installing a printer hard disk Note: Table of contents Troubleshooting The trade-off is that it takes smaller cartridges so printing costs are a bit higher.
Lexmark CN – C Color Laser Printer Manuals
Page xxx Exposing The main components in the exposure process are the system card, the printhead and the photoconductor unit. Installing Printer Software Before you start, perform the black alignment Registration. Ensure that the top access door is closed before removing the linkage screw. Page xxx Remove the screw B exposed after removing the exit tray. Page xxx Installation notes: Loading Paper And Specialty Media Also See for C Technical reference – pages User manual – pages Reference manual – 55 pages.
Expandable Memory Options Yes Interface: Using The Multipurpose Feeder We encourage the recycling of our products.
Xx—mirror Motor Service Check Align and place the eight keyholes on the system board metal plate onto the screws on the system board. Page 10 Using labels Print samples on the labels being considered for use before buying large quantities. The other parts regularly required are the pick rollers.
Lexmark C532 Manuals
The user manual recommends running the alignment procedure. Lexmark Xe, Xe, And Xe C, C, C, C Maunal Printer Menus When the message “82 Waste Toner Box Neatly Full” appears it is nearing time to replace the box so make sure one is on order. Failure to do this allows the printhead to fall out of the printer, potentially damaging the printhead.
The printer takes toners frequently, photoconductors less frequently, a waste toner box sometimes. Lexmarm Of Limited Warranty Paper And Specialty Media Guide Do not install the camshaft assembly by reversing the removal procedures.
Replace Pc Unit Transfer Belt Removal Page xxx Toner cartridge The following illustration shows the circuit path that allows high voltage current to flow from the HVPS to the toner cartridge. Paper Sensing xxx Paper sensing Sensors are strategically placed in the printer to ensure that the mmanual media is making msnual to specific points within a given time in the electrophotographic process.
Any information not previously stored on the hard disk is deleted.
Tray Linking Does Not Work Be careful not to c352n the cables that route through the top frame of the printer. Remove the paper pick mechanism assembly. If the left side of the camshaft assembly becomes disassembled, use the following illustration: Toner Level Sensor Removal Transparency print quality is poor Cause You are using transparencies that do not meet the printer specifications.
Lexmark C Manuals
Page xxx Fusing After the image has been transferred onto the print media, it is ready for fusing. Identifying The Paper Path Lesmark prevent print quality problems, avoid getting fingerprints on the transparencies. If you are replacing a new printhead, perform the entire printhead alignment.
Printing A Font Sample List When the top door is closed with the front access door also closed, the drive retraction lockout trips the switch arm which closes the 24 V dc interlock switch.
The top cartridge motor 1 on the EP drive assembly provides drive to the top two photoconductor units and toner cartridges yellow and cyan. This setting only appears if the Maintenance Warning and Intervention function is enabled in the printer Configuration ID.
Replace the front door Go to step 2. To avoid damaging the photoconductor drum, hold the photoconductor units by their handle and place the photoconductor units on a clean surface.